Starlight Group Held the Fifth Round of "100-Day Safety and Zero Accident" Campaign Launch Conference


Release time:

2016-11-22

On November 21, 2016, Starlight Group held the fifth round of "100-day Safety and Zero Accident" event kick-off meeting. The meeting was held in the multimedia teaching room of Starlight Group Service Center. It was presided over by Xing Xiaofeng, Minister of Sustainable Development of the Group. Pan Yongsheng, deputy general manager of the group, and the general managers of each branch were seated on the rostrum. This meeting summarized the fourth round of "100-day safety and zero accident" activities. In the fourth round of "100-day safety and no accident" activities, all branches comprehensively investigated the safety risks around them, and improved the safety risk point investigation and management system, standards and list. Sustainability of each branch

图片

On November 21, 2016, Starlight Group held the fifth round of "100-day Safety and Zero Accident" event kick-off meeting. The meeting was held in the multimedia teaching room of Starlight Group Service Center. It was presided over by Xing Xiaofeng, Minister of Sustainable Development of the Group. Pan Yongsheng, deputy general manager of the group, and the general managers of each branch were seated on the rostrum.
This meeting summarized the fourth round of "100-day safety and zero accident" activities. In the fourth round of "100-day safety and no accident" activities, all branches comprehensively investigated the safety risks around them, and improved the safety risk point investigation and management system, standards and list.


The sustainable development department of each branch shall strengthen the organization and leadership, overcome difficulties, and complete the work tasks with good quality and quantity, so as to lay a good foundation for the development of this round of 100-day zero accident activities.
Zhu Yonggui, Deputy Minister of Sustainable Development of the Group, read out the "Notice of Starlight Group on Launching the Fifth Round of" Safety Production for 100 Days and Zero Accidents ": The main contents are as follows:
(I) continue to work hard to complete the fourth round of 100-day safety zero accident activities
The fourth round of 100-day safety zero accident activities requires all branches to comprehensively investigate the safety risks around them and improve the safety risk point investigation and management system, standards and list. According to the requirements of this round of activities, units that have not completed the work requirements of the fourth round of activities must strengthen organization and leadership, overcome difficulties, and complete work tasks with quality and quantity, so as to lay a good foundation for the development of this round of 100-day zero accident activities.
(II) to find out the major risk points and solve the "unexpected" problem
All units should firmly establish red line awareness and bottom line thinking, and fully grasp the situation of major risk points in their jurisdiction. The safety management department shall control the major risk points of the unit and submit them to the main person in charge of the unit and the sustainable development department of the group, so that the main person in charge and relevant personnel can have a clear idea, be prepared for danger, be calm in case of trouble, and firmly grasp the initiative.
(III) implement the responsibility of major risk supervision and solve the problem of "not being able to manage".
The safety management departments of each unit shall, in accordance with the principle of "classification and territory", implement the supervision responsibilities for the major safety risk points in their jurisdiction one by one, and ensure that each risk point is responsible, has preventive measures, and has emergency response countermeasures.
(IV) Standardize and Refine the Construction of Safety Management System
Safety management system, files, ledgers, etc. are important aspects of safety work, the guiding ideology and basis of our daily safety work, an important form of safety work records and archives, and an important content of supervision and inspection by higher-level safety supervision departments. The construction of safety management system is a long-term process and needs to be continuously improved. This activity requires all branches and units to enrich, improve and refine the safety management system, files and ledgers according to the "basic file contents and details of safety production management" compiled and formulated in the first half of this month, and in combination with their own actual conditions, so as to comprehensively improve the internal level of safety management of the company.
(V) comprehensively do a good job in winter production safety











In winter, all kinds of safety accidents are prone to occur. All units focus on strengthening management and training in fire control, hot work, electricity consumption, transportation, etc., resolutely put an end to illegal operations and behaviors, and eliminate potential safety hazards in time.
Pan Yongsheng, deputy general manager of the group, summarized the work of the fourth round of "100 days of safe production and zero accidents": 1. The accident rate is reduced: compared with the previous rounds of activities, both production accidents and traffic accidents are significantly reduced.
2. Further implement the safety production responsibility system: all companies have continuously strengthened the safety production knowledge training for employees, so that the safety awareness of employees has been continuously improved; the leaders of each company have organized joint inspections, self-inspection and self-inspection to promote safety Production work; grassroots employees can actively find potential safety hazards in their work and make rectifications to prevent safety accidents; at present, from the general manager, production minister, workshop director, to the team staff, the safety production responsibility system of each company has been gradually improved, the safety responsibilities of each department have been gradually clarified, and the joint efforts of joint management have been continuously enhanced.
3. Management of employee safety protection equipment: employees have formed consciousness on the wearing of protective clothing and safety helmet, and the leaders of various companies have also organized relevant inspection work, and achieved good results.
4. The safety warning signs in the factories and workshops of each company are made in accordance with national standards, registered and managed in a unified and standardized manner.





General Manager Pan put forward several requirements for the fifth round of safety production 100-day zero accident activities: 1. All branches and departments, in consolidating the achievements of the previous four rounds of safety zero accident activities, continue to do a good job in safety production management, improve the safety management level of our leaders, continue to promote the management system of part-time safety officers, improve the investigation and list of safety risk points, and fully grasp the situation of major risk points in their jurisdiction, be prepared, have a clear idea, and fall to the people. We should conscientiously investigate the key parts and links of safety, take more stringent measures, more effective methods, and more patient and meticulous work, and resolutely put an end to and eliminate the occurrence of all kinds of safety accidents.
2. Now it has entered winter, the weather is cold, and the potential safety hazard for employees to commute is relatively large. Companies should pay attention to it and strengthen traffic safety training. There must be no paralysis and fluke mentality.
3. Continue to carry out benchmarking learning, learn from each other's advanced management experience and working methods, and improve the company's safety management level, especially in terms of safety management work ideas, safety management rules and regulations, learn from companies that have done well, and make safety management Level to a new level, and strive to move towards the direction of safety production standardization. Managers at all levels must implement their own safety responsibilities, grasp the grassroots, and establish a set of rigid restraint mechanisms to make employees aware of the importance and necessity of safe production. Accidents are often caused by non-compliance with safety operation procedures and illegal operations. Employees are required to operate unconditionally according to the procedures, visit the site and inspect the operating environment in person.
4. The company's outstanding problems (noise, smell, dust, hazardous waste, etc.), to continue to carry out special rectification work, absolutely can not relax.
5. Strengthen the safety management of outsourcing contractors, sign a safety agreement, require them to carry out accident insurance, to avoid losses to the company, the company should strengthen supervision.
Pan finally concluded that safety work has a long way to go, and we must "standardize safety management, thoroughly solve the problems of" unexpected "and" unmanageable ", and strive to improve the intrinsic safety level of enterprises".
Especially now that domestic safety production accidents occur frequently, we must take accidents as a lesson and take strong measures to effectively do a good job in safety production to ensure a good safety production environment for the group.






Key words: